Then unplug the board from your PC and start at the beginning again by downloading and installing the drivers first. The instructions below recommend using Tarot Gimbal Firmware v1. Connect the gimbal to your computer using the USB dongle. Follow the instructions below to update both the controller and motor firmwares. The gimbal must be running firmware version 1. Download and unzip the Tarot Gimbal Firmware v1. 
| Uploader: | Shashura |
| Date Added: | 13 November 2010 |
| File Size: | 61.36 Mb |
| Operating Systems: | Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X |
| Downloads: | 79677 |
| Price: | Free* [*Free Regsitration Required] |
Then unplug the board from your PC and start at the beginning again by downloading and installing the drivers first.
This issue can apparently be resolved according by following instructions on this web page: Disconnect the battery from the gimbal so that it is not powered. Do not touch the gimbal while it is starting up. The gimbal must be running firmware version 1.
Note The instructions below recommend using Tarot Gimbal Firmware v1. It should be possible if you can get the drivers to work as in the link in this article above.
FLYING MODEL AIRPLANE
The instructions above describe a setup so that only controls the Tilt i. There will be another progress bar indicating the status of the upgrade. The Tarot T-2D has been a popular low cost 2-axis brushless gimbal. Now you will need to manually select the correct version driver to gimbzl, this will be done via the device manager.
Then click on the update driver button and follow the menus as shown in the picture below until you can select the version 3. While this actual hardware has been retired and manufacturer support discontinued, this page is intended to keep up basic support for this item, as well as to serve as an illustrative example of how to configure ardupilot gimbal control options.
To verify that the firmware has updated successfully, disconnect and reconnect the battery. If drivers cannot be found you may be able to install Windows 7 or Windows XP drivers using one of the.
If this is the first time you have plugged in the dongle you will likely see a USB device installation window.
Tarot T-2D Gimbal - Configuration & Operation |
Follow the instructions below to update both the controller and motor firmwares. Select this and press Write Settings To Flash.
If you dont have any options on the last screen then either you did not properly install the version 3.
Disconnect and reconnect the battery from the gimbal to complete the upgrade process.
The instructions below recommend using Tarot Gimbal Firmware v1. Many customers often have an issue when it comes to configuring their T-2D brushless gimbal if they are using a windows 8 or 8. This should cause the gimbal to tafot down at about 45 degrees. However I have not played with the T-2D settings for a few months so cant recall if I was on windows 8 or windows If you plan to use 4S or higherplease use a gumbal regulator to ensure the voltage stays within safe operating limits: Leave the gimbal unpowered for now.
Upon powering your vehicle, the gimbal will display a solid yellow light while it is starting and calibrating.
Selecting the correct driver from the device manager Now you will need to manually select the correct version driver to use, this will be done via the device manager. Download and unzip the Tarot Gimbal Firmware v1. After a few seconds the image gibal the camera should begin moving as the gimbal is moved. 2r the new versions of the Prolific USB drivers dont seem to work with the T-2D usb dongle, the only thing that I found to work was to use an older version 3.
Ensure that the same COM glmbal as before is selected the gimbal controller and motor controller use the same COM port Now select Open Firmwarebut this time select the. Connect the gimbal to your computer using the USB dongle. You will see a green progress bar on the screen indicating the status of the update.
If the gimbal is not connected to the autopilot, it will perform basic stabilization without autopilot control, indicated by a solid blue light.
Комментарии
Отправить комментарий